PRODUCT CERTIFICATIONS
OVERVIEW All 475 Field Communicators come with the main unit label (see
Figure B-1). Intrinsically Safe (KL option) 475 Field Communicators
also have an additional label opposite the main unit label on the back
of the Field Communicator. If the 475 Field Communicator does not
contain this label (NA option), then it is considered non-IS approved.
The Declaration of Conformity and other approval information are
available on www.fieldcommunicator.com.
The Federal Communications Commission (FCC), Industry Canada
(IC), Telecommunications Regulatory Authority (TRA), and Radio and
Telecommunications Terminal Equipment (R&TTE) approvals apply to
only 475 Field Communicators licensed for Bluetooth. A labels appears
on the back of the Field Communicator if it is licensed for Bluetooth.
APPROVED
MANUFACTURING
LOCATIONS
R. STAHL HMI Systems GmbH —Cologne, Germany
FCC This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
user’s manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any modifications made to this device that are not approved by
Emerson Process Management may void the authority granted to the
user by the FCC to operate this equipment.
IC This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
100
TELECOMMUNICATIONS
REGULATORY
AUTHORITY
OMAN - TRA TRA/TA-R/0089/11 D080273
EUROPEAN DIRECTIVE
INFORMATION - CE
COMPLIANCE
R&TTE (1999/5/EC) This equipment is in conformity with the Radio and
Telecommunications Terminal Equipment (R&TTE) Directive
1999/5/EC, ETSI EN 300328:2006-10, and IEC 2209-2:2007
standards.
Electro Magnetic
Compatibility
(2004/108/EC)
Tested to the EN 61326-1:2006 and ETSI EN 301489-17:2002-08
specification.
Low Voltage (2006/95/EC) Tested to the EN 61010-1:2001 specification.
ATEX Directive (94/9/EC)
(KL option only)
See “European Certifications” for more information.
HAZARDOUS LOCATIONS
CERTIFICATIONS (KL
OPTION ONLY)
The Intrinsic Safety approvals listed in this section include compliance
with the FISCO requirements.
European Certifications ATEX Intrinsic Safety (KL option only)
This equipment complies with the ATEX Directive (94/9/EC).
Specific ATEX Directive Information is located within this section and in
the 475 Field Communicator Getting Started Guide.
Applicable standards EN 60079-0:2012, EN 60079-11:2012, and EN
60079-26:2007.
Certification No.: BVS 09 ATEX E 022
II 2 G (1 GD) Ex ia [ia Ga] [ia Da IIIC] IIC T4 Gb (-10°C ≤ Ta ≤
+50°C)
0158
HART Intrinsically Safe Electrical Parameters
Input Parameters
Ui = 30 Volt DC
Ii = 200 mA
Pi = 1.0 Watt
Li = 0
Ci = 0
101
FOUNDATION fieldbus
The FISCO standard applies to the FM, CSA, IECEx, and ATEX
certifications.
Intrinsically Safe FISCO
Intrinsically Safe Non-FISCO
International Certification IECEx
Certification No.: IECEx BVS 10.0094
Ex ia [ia Ga] [ia Da IIIC] IIC T4 Gb (-10°C ≤ Ta ≤ +50°C)
HART Intrinsically Safe electrical parameters
Input Parameters
Output Parameters
FOUNDATION fieldbus
Intrinsically Safe FISCO
Intrinsically Safe Non-FISCO
North American
Certifications
Factory Mutual (FM)
Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D and
Class I, Zone 0, AEx ia IIC T4 (Ta = 50°C) hazardous locations when
connected as indicated in the control drawing 00475-1130. See the
control drawing for input and output parameters.
Canadian Standards Association (CSA)
Intrinsically Safe for use in Class I, Zone 0, Ex ia IIC T4 (Ta = 50°C)
Output Parameters
U0 = 1.9 Volt DC
I0 = 32 μA
UiIIC = 17.5 Volt DC IiIIC = 215 mA PiIIC = 1.9 Watt
UiIIB = 17.5 Volt DC IiIIB = 380 mA PiIIB = 5.3 Watt
U0 = 1.9 Volt DC I0 = 32 μA
Ui = 30 Volt DC Ii = 380 mA Pi = 1.3 Watt
U0 = 1.9 Volt DC I0 = 32 μA
Li = 0 Ci = 0
Ui = 30 Volt DC
Ii = 200 mA
Pi = 1.0 Watt
Li = 0
Ci = 0
U0 = 1.9 Volt DC
I0 = 32 μA
UiIIC = 17.5 Volt DC IiIIC = 215 mA PiIIC = 1.9 Watt
UiIIB = 17.5 Volt DC IiIIB = 380 mA PiIIB = 5.3 Watt
U0 = 1.9 Volt DC I0 = 32 μA
Ui = 30 Volt DC Ii = 380 mA Pi = 1.3 Watt
U0 = 1.9 Volt DC I0 = 32 μA
102
hazardous locations when connected as indicated in the control
drawing 00475-1130. See the control drawing for input and output
parameters. Please note the parameters in the control drawing are the
same as the FM parameters.
POWER
SUPPLY/CHARGER
CERTIFICATION
Declaration of
Conformity/Approvals
The 475 Field Communicator power supply/charger complies to the
requirements of the relevant EU directives. The conformity
assessment process has been successfully completed as per the
directives listed below. All approval information for this product can be
accessed at www.fieldcommunicator.com.
European Union Directives
Low Voltage Directive 2006/95/EC
EN 60950: 2001 + A11
EMC Directive 2004/108/EC
The following harmonized standards were applied, immunity
EN61204-3:2000
RoHS (2002/95/EC) directive
WEEE (2002/96/EC) directive
Japanese Directives
DENAN/PSE
LABEL DRAWINGS
Figure B-1. All 475 Field Communicators have a similar label to the one below.
2009 08 50 1
Manufactured Exclusively for
Fisher-Rosemount Systems, Inc.
(an Emerson Process Management company)
By R. STAHL HMI Systems GmbH
D-50767 Cologne, Germany
Use only with 475 Power Module
20nn
Barcode
0158
475 Field Communicator
Serial No. 1 2 3 4 5 6 7 8
44.0mm
33.0 mm
Label 1-1
ZN:2009 08 50 1
R = 1.5 mm
103
Figure B-2. Approval Ex Label Example (Only on 475 Field Communicators with the KL